Schoeps CMC 65 Matched Cardioid/Omni Stereo Set

Schoeps CMC 65 Matched Cardioid/Omni Stereo Set

CMC 6 U

The CMC 6 U is designed for standard 48 and 12-Volt phantom powering, its circuitry recognises the supply voltage and adjusts itself automatically and the performance characteristics essentially remain the same either way. The main difference is that the current drawn at 12 Volts is greater than at 48 Volts, however the 12-Volt mode consumes less power and might be more favourable for battery power3ed recording applications and scenarios.

The microphone amplifier is responsible for proving the necessary electrical charge to the mics capsule, without which it would then be unable to generate any signal. Since the capsule’s output signal is very weak (Hi-Z), it must then be amplified in order for it to reach the next stage in the signal chain and must undergo balancing and impedance matching before this transition. The CMC 6 incorporates a balanced, direct-coupled class-A amplifier, yielding a low output impedance, high RF shielding and minimal distortion.

Key Features:

• Flat frequency response
• Very low harmonic distortion and noise
• Works with 12V and 48V phantom power
• Balanced, low-impedance output
• High suppression of interference on the microphone cable
• Excellent protection against high-frequency radio interference with "RFI Shield"
• Frequency-independent impedance
• Signal transmission possible over very long cables
• Reliable operation even with weak phantom power
• Symmetrical, transformer- and capacitor-free output stage with a class-A amplifier
• Above 20 kHz, the signal is attenuated for protection against interference in the ultrasonic range, e.g. through the ultrasonic autofocus of a film camera

Specifications:

• Maximum sound pressure level (THD < 0.5 %): with MK 4: 131 dB-SPL (P48, P12)
• Frequency range: 20 Hz - 20 kHz
• Sensitivity: see corresponding capsule
• Maximum output voltage: 1 V (0 dBV) with 1 kΩ load
• Low cut filter: 20 Hz, 12 dB/oct.
• Minimum recommended load impedance: 1 kΩ
• Output impedance: 42 Ω
• Maximum cable length: > 400 m / ~1300ft
• SCHOEPS RFI Shield: Yes
• Powering standard / Valid range: P48 / 20-52 V | P12 / 10-13 V
• Current consumption: 4 mA (P48) | 8 mA (P12)
• Common mode rejection ratio (at 1 kHz): > 55 dB
• Output: XLR-3M, analogue, 1 channel
• Length: 116mm
• Diameter: 20mm
• Weight: 60g
• Surface finish: Matte grey

MK 5 Microphone Capsule

With the Schoeps MK 5, polar pattern switching is purely mechanical, all via a sliding lever on the side of the capsule. With each setting it is like having an independent microphone capsule with the same quality as the MK 2S/MK 4 and very similar frequency and polar response characteristics. In contrast to most dual diaphragm microphones, the cardioid setting on the MK 5 maintains its directivity even at the lowest frequencies and has high frequency response up to 20kHz. Additionally, the MK 5 has an excellent low frequency response in the omnidirectional setting along with the low sensitivity towards wind, vocal plosives and solid-borne sound typical of pressure transducers.

Key Features:

• Mechanical switching between omnidirectional and cardioid patterns
• True one-diaphragm system (unique on the microphone market)
• Pure pressure transducer in the omni setting; pressure gradient transducer in the cardioid setting
• Can be used in nearly any situation; often suggested as an initial acquisition. Popular with training institutes

Specifications:

MK 5 - OMNI

• Pickup pattern: Omnidirectional
• Frequency range: 20 Hz - 28 kHz with CMC 6 / CMR |20 Hz - 43 kHz with CMC 6xt
• Sensitivity: -38,0 dB (V/Pa), 12 mV/Pa with CMC 6
• Equivalent noise level (A-weighted): 12 dB with CMC 6
• Equivalent noise level (CCIR): 24 dB with CMC 6
• Signal-to-noise ratio (A-weighted): 82 dB with CMC 6
• Maximum sound pressure level (THD < 0.5 %): 132 dB-SPL with CMC 6

MK 5 - CARDIOID

• Pickup pattern: Cardioid
• Frequency range: 40 Hz - 26 kHz with CMC 6 / CMR | 40 Hz - 41 kHz with CMC 6xt
• Sensitivity: -37 dB (V/Pa), 14 mV/Pa with CMC 6
• Equivalent noise level (A-weighted): 13 dB with CMC 6
• Equivalent noise level (CCIR): 23 dB with CMC 6
• Signal-to-noise ratio (A-weighted): 81 dB with CMC 6
• Maximum sound pressure level (THD < 0.5 %): 131 dB-SPL with CMC 6

Mechanical Specifications

• Length: 27mm
• Diameter: 20mm
• Weight : 25g
• Surface finish: Matte grey