Focusrite RedNet D16R MkII

I/O Level Trim

• Input trim range: Mute, then -78 dB to 0 dB in 1 dB steps (per channel)
• Output trim range: Mute, then -78 dB to 0 dB in 1 dB steps (per channel)

Input Sample Rate Converters

• Sample Rate: Range 32 to 216 kHz
• Gain Error: -0.3 dB
• Dynamic Range: > 138 dB (-60 dBFS method)
• THD+N: < -130 dB (0.00003%); 0 dBFS input
• Latency: 11 to 45 samples (network and input sample rate dependent)

Digital Performance

• Supported Sample Rates: 44.1 / 48 / 88.2 / 96 / 176.4 / 192 kHz (-4% / -0.1% / +0.1% / +4.167%) at 24 bit
• Clock Sources: Internal, Word Clock, DARS, AES input 1-2, AES input 9-10 or from Dante Network Master
• External Word Clock Range: Nominal sample rate ±7.5%

Rear Panel Connectivity

AES3

• Channel Count: 16 x 16 AES3 channels
• Input and Output: 2 x DB25 connectors (AES59 Combined I/O / Tascam Digital)
• Alternate Input (optional DARS): 1 x Female XLR-3 (replaces DB25 channels 1-2)
• Alternate Output: 1 x Male XLR-3 (duplicates DB25 channels 1-2)

S/PDIF

• Channel Count: 2 x 2 S/PDIF Channels (reduces AES3 input channels)
• Input: 1 x RCA phono socket (replaces DB25 channels 3-4)
• Output: 1 x RCA phono socket (switchable, duplicates any DB25 channel pair)

Word Clock

• Input: 1 x BNC 75Ω (switchable termination)
• Output: 1 x BNC 75Ω

PSU & Network

• PSU: 2 x IEC Inputs with retaining clips
• Network: 2 x etherCON NE8FBH, also compatible with standard RJ45 connectors (Accommodates rugged etherCON NE8MC* - Does not mate with Cat 6 cable connector
• NE8MC6-MO and NKE65* cable)

Front Panel Indicators

• PSU A: Green LED. Illuminates when an AC input is applied and all DC outputs are present
• PSU B: Green LED. Illuminates when an AC input is applied and all DC outputs are present
• Primary Network: Green LED. Indicates that a network connection is present on primary port when in redundant mode. When in Switched mode, a valid network connection at either Primary or Secondary network port will cause this LED to illuminate
• Secondary Network: Green LED. Indicates that a network connection is present on secondary port when in redundant mode. Not used in switched mode Sync Locked Green LED. When unit is network slave, shows valid network lock. When network master shows unit is locked to indicated clock source. Flashing indicates invalid external clock present and unit has reverted to internal clock
• Sample Rate: Orange LED for each: 44.1 kHz, 48 kHz, x2, x4
• Pull Up/Down: Orange LED. Indicates unit is set to operate on a Dante pull up/down domain
• Signal Indicators: 16 Green LEDs: 8 input/8 output indicators. Illuminate at -126 dBFS
• Clock Source: Orange LED for each: Internal, Word Clock, DARS, Input 1–2, Input 9–10

Network Modes

• Redundant: Allows unit to connect to two independent networks
• Switched: Connects both ports to integrated network switch allowing daisy-chaining of devices

Dimensions

• Height: 44.5mm / 1.75” (1RU)
• Width: 482.6mm / 19”
• Depth: 263mm / 10.35”

Weight

• Weight: 3.84 kg / 8.47 lbs

Power

• PSUs: 2 x Internal, 100-240 V, 50/60 Hz, consumption 30 W